Use a movable faucet to remove bacteria and waste water. It is easy to install and even easier to use.

The kitchen faucet is one of the dirtiest places in your home. After handling raw meat or biscuit dough, turn on the tap immediately for dirty hands, and bacteria will spread to the handle. Moreover, unless the faucet is disinfected after each use, dirt will accumulate.

Install a hands-free kitchen faucet to permanently remove bacteria. The device is motion activated, so it will record the movement of your hand and turn it on automatically when you need to wash. This is a win-win situation: you will save time and water while promoting your health! In addition, the installation of non-contact faucet is quite simple.

What do you need?

• No-touch faucet and included hardware (we used the Arbor kitchen faucet from Moen)
• Batteries
• Drill
• 3/32 drill bit
• Screwdriver
• Adjustable wrench
• Tape measure

Step 1: place the faucet

Turn off the hot and cold water supply to the kitchen sink. Remove the old faucet and thread the data cable, hose and handle of the new faucet through the deck gasket. Align with the bottom of the faucet body. Then insert the cable, hose and rod through the mounting hole. If there are multiple holes, install the cover plate. Before continuing, make sure the faucet handle is on the right and the nozzle is facing you.

Step 2: fix the faucet

Under the sink, slide the support plate onto the cable and then slide the mounting washer onto the faucet handle. Ensure that the data cable and hose are within the curve of the gasket. china automatic sensor faucet factory Screw the mounting nut onto the faucet handle and ensure that the faucet is correctly positioned on the counter or sink. Tighten the nut with the mounting tool provided.

Editor's note: insert the screwdriver into the hole at the bottom of the plate. It makes tightening easier.

Step 3: install the hose bracket

Install the hose bracket approximately 2 inches from the end of the connecting hose. Slide the bracket onto the end of the faucet and secure in place with the hose guide nut. Guide into the faucet spout. Remove the protective cover from the end of the hose and connect it to the faucet with the quick connect line. Simply press, hold and listen for a click indicating a secure connection.

Step 4: connect the hose and supply line

Connect the hose and oil supply pipe by identifying the corresponding inlet on the control box. Remove the protective caps from the hoses and push each cap into place. Pull gently to ensure that each hose is secure. Connect the hot and cold water supply pipes. china touchless bathroom faucet manufacturer Fix the connection with an adjustable wrench. The connection shall be close, but not too tight. Connect the cold noodles in the same way.

Edit tip: make sure the correct water pipe is connected to the correct inlet. To distinguish between the two, note that the hot water supply line has a white label.

Step 5: install the control box

Install the control box by clamping it into the hose guide nut. If you want to install the control box on the cabinet base, install it where the data cables and hoses can reach.

Step 6: connect the spray bar

Remove the protective cover of the hose and ensure that the rubber gasket and screen are in place, and connect the spray bar to the pull-down hose. Screw the spray bar onto the pull-down hose and tighten it with an adjustable wrench until the hose nut is flush with the spray bar. Be careful not to be too tight. Find the white mark on the pull-down hose and install the counterweight under it.

Step 7: install the battery pack

When installing the battery pack, ensure that the wires can reach the bottom of the control box. Remove the cover, insert the battery, and replace the cover. The battery pack can be fixed on the wall with double-sided adhesive tape or with screws.

Step 8: insert the data cable

Remove the protective cover and insert the data cable into the control box. Make sure the Mini USB connection is properly aligned with the data port. Use zipper tape to tie the hose and cable together, china motion activated faucet manufacturers except pull-down hose. Then insert the battery pack lead into the control box. Make sure there is nothing within 3 feet of the faucet sensor to ensure proper startup. A blue light will flash at the bottom of the faucet.

Step 9: turn on the water

Reopen the hot and cold water inlets. To ensure that the pull-down hose works properly, make sure that no cleaning supplies or objects hinder the movement under the hose